How to Tie a Ronnie Rig: A Step-by-Step Guide

The Ronnie rig, also called the spinner rig, presents a pop-up just off the lakebed on a hook that pivots on a swivel, so it resets itself and hooks fish that other rigs miss. You tie it from a curve shank hook, a size 11 spinner swivel, a hook ring swivel for the bait, a kicker, and a stiff boom section. Here’s exactly how, and when to use it.
What you’ll need
A size 4 to 6 curve shank hook, a size 11 quick-change spinner swivel, a small hook ring swivel and hook bead, a kicker (or a length of shrink tube), an anti-tangle sleeve, rig putty, and 15 to 20lb stiff coated braid or fluorocarbon for the boom. Everything here is in our carp hooks and swivels and quicklinks sections, plus rig tools if you’re starting your kit.
Tying it, step by step
Step 1: Mount the bait swivel
Slide the hook ring swivel onto the shank of the hook, then trap it in place with a hook bead sitting roughly opposite the barb. This little swivel is what the pop-up attaches to, and its position controls how the rig sits.
Step 2: Fit the hook to the spinner swivel
Push the eye of the hook onto the crook of the size 11 spinner swivel. That loose, free-spinning connection is the whole trick of the Ronnie.
Step 3: Lock it with a kicker
Slide a kicker over the hook eye and the crook to hold everything in line. Shrink tube steamed over a kettle and set with a slight curve does the same job and some prefer it. The kicker also makes the hook flip aggressively in the mouth.
Step 4: Tie on the boom
Attach your boom section, 15 to 20lb fluorocarbon or stiff coated braid, to the other end of the spinner swivel. Boom length is typically 4 to 6 inches; longer over very soft silt.
Step 5: Tidy with a sleeve
Slide an anti-tangle sleeve down over the swivel junction. It kicks the rig away from the lead and stops wrap-arounds on the cast.
Step 6: Mount the pop-up
Screw or tie a 12 to 15mm pop-up to the hook ring swivel. Bright or washed-out, whatever the lake responds to; our boilies and pop-ups range has you covered.
Step 7: Balance with putty
Mould a pea of rig putty onto the boom just below the swivel. You want the pop-up sinking slowly, settling so the bait sits an inch or so off the deck with the hook ready underneath. Always test it in the margins before casting out, ten seconds that saves whole sessions.
When does the Ronnie beat other rigs?
Over silt, leaf litter, and low weed, anywhere a bottom bait would be half-buried, the Ronnie keeps the bait visible and the hook point clean. It’s also the rig for fishing over a scattering of boilies, and because it resets after a pluck, it keeps fishing when single-chance rigs are done. On clean, polished gravel a simple bottom-bait rig from our five essential carp rigs guide is often the better pick.
FAQs
What size pop-up for a Ronnie rig?
12 to 15mm suits a size 4 to 6 hook. The bait should just lift the hook, not fight the putty.
Ronnie rig or chod rig?
Both present pop-ups. The chod shines cast at range onto unknown or weedy bottoms; the Ronnie is neater fished on a spot you know. On most day ticket lakes the Ronnie is the more efficient hooker.
Does the Ronnie rig work with barbless hooks?
Yes. Plenty of venues insist on barbless and the rig loses little. Keep the hook needle sharp and maintain steady pressure in the fight.
Can I buy Ronnie rigs ready-tied?
Yes, our pre-tied carp rigs include spinner rigs tied with quality components. Handy to copy when tying your own.
Stuck on any step? Bring your bits into Claytons Tackle at 4 Queen Street, Haverhill and we’ll tie one with you at the counter. It takes five minutes to learn with the right parts in front of you. Call 01440 810120.